Difference between revisions of "Building a stack"
Head Monkey (Talk | contribs) m (→To-do) |
Head Monkey (Talk | contribs) |
||
(6 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
− | Once the boards are ready to go the next step is to sort | + | Once the boards are ready to go, the next step is to sort through them and find nine that make a reasonable stack. The boards don’t have to be perfectly straight. If they are all bent in the same way, that's fine. If the stack is a bit bowed end-to-end, we can correct that later. |
+ | |||
+ | When selecting boards to form a stack, it's important that they all be as similar as possible. The broad sides should be as close to smooth as you can get them. We’ll make them perfectly smooth later, so the smoother they are at the beginning, the less waste there will be later. | ||
<gallery caption="Matching boards into individual stacks."> | <gallery caption="Matching boards into individual stacks."> | ||
Line 10: | Line 12: | ||
Once you have a set of boards ready to go, lay them out on a bench in the order and orientation that you’ll be needing them during glue up. | Once you have a set of boards ready to go, lay them out on a bench in the order and orientation that you’ll be needing them during glue up. | ||
− | I use 8 [[Pipe Clamps|pipe clamps]], each with 12” wide 2” x 2” oak cauls on each side. I will alternate these on each side of the stack as I clamp it, so I start with half of the clamps on my workbench spaced to ensure that the other half wont overlap them much. I place | + | I use 8 [[Pipe Clamps|pipe clamps]], each with 12” wide 2” x 2” oak cauls on each side. I will alternate these on each side of the stack as I clamp it, so I start with half of the clamps on my workbench spaced to ensure that the other half wont overlap them much. I place butcher's paper under the clamps to protect the workbench from dripping glue. |
− | A fine spray of clean water on the boards | + | A fine spray of clean water on the boards adds a bit of moisture, which will help the glue cure properly. |
<gallery caption="A stack ready for layup."> | <gallery caption="A stack ready for layup."> | ||
Line 20: | Line 22: | ||
− | I use [[Polyurethane glue]] for my stacks because it has a reasonably long working time | + | I use [[Polyurethane glue]] for my stacks because it has a reasonably long working time. It will take about 15 min to actually get a single stack clamped up. I take the cap off the bottle and pour a bead of glue down the entire length of the first board. Then, I spread it with a plastic spreader the same way I spread epoxy during layup. (I use old bits of base material as a spreader here.) |
+ | |||
+ | It takes some practice to start to recognize how much glue to apply in a single pass. Start with too little and add more but don’t take too much time as there are seven more applications to make. Take the next board and lay it in place on top of the first one, then rinse and repeat. Once the final board is in place, you’ll have a gooey stack ready to be clamped. | ||
<gallery caption="Applying glue to a stack."> | <gallery caption="Applying glue to a stack."> | ||
Line 31: | Line 35: | ||
− | Carefully push the stack over so it lays flat on the bottom set of clamps | + | Carefully push the stack over so it lays flat on the bottom set of clamps. Adjust the board placement as necessary. Note that the ends of the stack don’t have to align perfectly! It’s common to have boards of slightly different lengths and that’s okay; we’ll trim it up later. |
<gallery caption="Laying down the stack for clamping."> | <gallery caption="Laying down the stack for clamping."> | ||
Line 40: | Line 44: | ||
− | Once the boards are aligned, tighten the center clamp on the bottom, | + | Once the boards are aligned, tighten the center clamp on the bottom. Then, add top clamps on either side and tighten them. Tighten two bottom clamps on either side of those. Repeat in the same manner until you reach the ends. Try to avoid getting any glue on the cauls. You don’t want to glue your clamps to the stack. You can also take precautions by putting tape on the cauls. |
<gallery caption="Clamping the stack."> | <gallery caption="Clamping the stack."> | ||
Line 48: | Line 52: | ||
− | I usually let a stack dry | + | I usually let a stack dry for three to four hours. I can make a few stacks per day. |
− | The [[Woodworking Resources]] page has a number of articles on proper clamping. These are all worth a read and will help you understand how much pressure you should use in order to get a good glue up. | + | The [[Woodworking Resources]] page has a number of articles on proper clamping. These are all worth a read and will help you understand how much pressure you should use in order to get a good glue-up. |
== Preparing the stack for slicing == | == Preparing the stack for slicing == | ||
− | Once the stack is dry and out of the clamps it | + | Once the stack is dry and out of the clamps, it needs to be prepared to be sliced. The first step is to remove all of the excess glue squeezed out during layup and clamping. This is easily done, as the polyurethane glue isn’t really structural. A [[Hand Scraper|hand scraper]] makes short work of it. You don’t need remove all of it, just any glue that would prevent the stack from laying flat on each side. |
<gallery caption="Scrape off excess glue"> | <gallery caption="Scrape off excess glue"> | ||
Line 62: | Line 66: | ||
− | The wide sides of the stack will be uneven, since it’s almost impossible to find boards that are perfectly straight | + | The wide sides of the stack will be uneven, since it’s almost impossible to find boards that are perfectly straight and to align them perfectly for clamping. I pick the side that looks the flattest and I run that over an 8” jointer until it is flat. I set the jointer to take off about 1/16th of an inch per pass. You want to remove the minimum amount of wood possible from now on. Pencil marks placed on the side being jointed beforehand make it easy to see which portions are smooth and where more work is needed. |
<gallery caption="First side being jointed"> | <gallery caption="First side being jointed"> | ||
Line 71: | Line 75: | ||
− | Once that face is flat, I turn the stack 90 degrees and flatten the bottom of the stack | + | Once that face is flat, I turn the stack 90 degrees and flatten the bottom of the stack. To do this, I place the newly flat face against the fence of the jointer. Now we have one flat wide face, one flat adjacent base and those two surfaces are at 90 degrees to each other. |
<gallery caption="Second side being jointed perpendicular to the first side"> | <gallery caption="Second side being jointed perpendicular to the first side"> | ||
Line 79: | Line 83: | ||
− | Next, I flatten the other wide face by running the stack thru a planer with the jointed side down. This yields a stack which has two good sides, and one good base. Surfacing the fourth face is optional at this point and I usually skip it. I | + | Next, I flatten the other wide face by running the stack thru a planer with the jointed side down. This yields a stack which has two good sides, and one good base. Surfacing the fourth face is optional at this point and I usually skip it. Then, I take the stack over to my chop saw and trim the ragged ends square, if necessary. |
<gallery caption="Third side being planed parallel to the first"> | <gallery caption="Third side being planed parallel to the first"> | ||
Line 98: | Line 102: | ||
− | Sometimes there are blemishes in the wood (knots, etc.) or uneven boards near the ends of a stack. That can be okay, | + | Sometimes there are blemishes in the wood (knots, etc.) or uneven boards near the ends of a stack. That can be okay, as long as these blemishes are beyond the ends of any reasonable core you will build. Stacks are often longer than actual cores. |
<gallery caption="Blemishes on a stack that really don’t matter"> | <gallery caption="Blemishes on a stack that really don’t matter"> | ||
Line 111: | Line 115: | ||
* [[Slicing a stack]] | * [[Slicing a stack]] | ||
* [[Joining the halves of a core blank]] | * [[Joining the halves of a core blank]] | ||
+ | |||
+ | [[Category:Core Blanks]] | ||
+ | [[Category:Woodworking]] |
Latest revision as of 23:24, 1 February 2012
Once the boards are ready to go, the next step is to sort through them and find nine that make a reasonable stack. The boards don’t have to be perfectly straight. If they are all bent in the same way, that's fine. If the stack is a bit bowed end-to-end, we can correct that later.
When selecting boards to form a stack, it's important that they all be as similar as possible. The broad sides should be as close to smooth as you can get them. We’ll make them perfectly smooth later, so the smoother they are at the beginning, the less waste there will be later.
- Matching boards into individual stacks.
Once you have a set of boards ready to go, lay them out on a bench in the order and orientation that you’ll be needing them during glue up.
I use 8 pipe clamps, each with 12” wide 2” x 2” oak cauls on each side. I will alternate these on each side of the stack as I clamp it, so I start with half of the clamps on my workbench spaced to ensure that the other half wont overlap them much. I place butcher's paper under the clamps to protect the workbench from dripping glue.
A fine spray of clean water on the boards adds a bit of moisture, which will help the glue cure properly.
- A stack ready for layup.
I use Polyurethane glue for my stacks because it has a reasonably long working time. It will take about 15 min to actually get a single stack clamped up. I take the cap off the bottle and pour a bead of glue down the entire length of the first board. Then, I spread it with a plastic spreader the same way I spread epoxy during layup. (I use old bits of base material as a spreader here.)
It takes some practice to start to recognize how much glue to apply in a single pass. Start with too little and add more but don’t take too much time as there are seven more applications to make. Take the next board and lay it in place on top of the first one, then rinse and repeat. Once the final board is in place, you’ll have a gooey stack ready to be clamped.
- Applying glue to a stack.
Carefully push the stack over so it lays flat on the bottom set of clamps. Adjust the board placement as necessary. Note that the ends of the stack don’t have to align perfectly! It’s common to have boards of slightly different lengths and that’s okay; we’ll trim it up later.
- Laying down the stack for clamping.
Once the boards are aligned, tighten the center clamp on the bottom. Then, add top clamps on either side and tighten them. Tighten two bottom clamps on either side of those. Repeat in the same manner until you reach the ends. Try to avoid getting any glue on the cauls. You don’t want to glue your clamps to the stack. You can also take precautions by putting tape on the cauls.
- Clamping the stack.
I usually let a stack dry for three to four hours. I can make a few stacks per day.
The Woodworking Resources page has a number of articles on proper clamping. These are all worth a read and will help you understand how much pressure you should use in order to get a good glue-up.
Preparing the stack for slicing
Once the stack is dry and out of the clamps, it needs to be prepared to be sliced. The first step is to remove all of the excess glue squeezed out during layup and clamping. This is easily done, as the polyurethane glue isn’t really structural. A hand scraper makes short work of it. You don’t need remove all of it, just any glue that would prevent the stack from laying flat on each side.
- Scrape off excess glue
The wide sides of the stack will be uneven, since it’s almost impossible to find boards that are perfectly straight and to align them perfectly for clamping. I pick the side that looks the flattest and I run that over an 8” jointer until it is flat. I set the jointer to take off about 1/16th of an inch per pass. You want to remove the minimum amount of wood possible from now on. Pencil marks placed on the side being jointed beforehand make it easy to see which portions are smooth and where more work is needed.
- First side being jointed
Once that face is flat, I turn the stack 90 degrees and flatten the bottom of the stack. To do this, I place the newly flat face against the fence of the jointer. Now we have one flat wide face, one flat adjacent base and those two surfaces are at 90 degrees to each other.
- Second side being jointed perpendicular to the first side
Next, I flatten the other wide face by running the stack thru a planer with the jointed side down. This yields a stack which has two good sides, and one good base. Surfacing the fourth face is optional at this point and I usually skip it. Then, I take the stack over to my chop saw and trim the ragged ends square, if necessary.
- Third side being planed parallel to the first
The stack is now ready for slicing.
- Cleaned up stack ready for slicing
Sometimes there are blemishes in the wood (knots, etc.) or uneven boards near the ends of a stack. That can be okay, as long as these blemishes are beyond the ends of any reasonable core you will build. Stacks are often longer than actual cores.
- Blemishes on a stack that really don’t matter